Tip: The AirPort Extreme has only one USB port, but you can connect multiple devices if you use a USB hub. You can use any old USB hard drive - even a USB thumb drive. (To set up an AirPort Extreme for the first time, see How to Set Up the AirPort Extreme.)Ĭonnect the USB hard drive to the AirPort Extreme. Make sure the AirPort Extreme is turned on and correctly configured. Here’s how to connect a hard drive to the AirPort Extreme: In the following sections, you’ll try accessing the network drive on your Mac and configuring the drive’s security settings. The first step is to actually connect the USB hard drive to your AirPort Extreme Base Station and let the AirPort know that the drive is plugged in. Connecting the Hard Drive to the AirPort Extreme It’s a great way to share documents, photos, music, and movies with the other people on your network. But did you know that you can also connect a USB hard drive to an AirPort Extreme? Doing so effectively creates a network drive that can be accessed by all of the users connected to the wireless network. You can use an AirPort Extreme Base Station to create a wireless network for the computers and devices in your home or office. How to Connect a Hard Drive to the AirPort Extreme.Towards the top right it SHOULD say: IP address:10.0.1.AirPort Apple Apps Backups Developer Education Email Hardware Internet iPad iPhone Mac Music Network Photos Security TV Weekend Wonk When your router's done updating, make sure your computer(or smartphone) can connect to the internet on your network like usual if you have older Apple routers, they'll flash amber til it's done, then solid green. It'll take 2-3 minutes for your router to update. It'll bring you back to the previous screen. Put a check in the little box next to "Enable default host at:" The ip address 10.0.1.253 should appear. Click "Network Options" towards the bottom It'll bring you back to the previous menu. Type in Xbox One or whatever(doesn't matter what you use, it's just a title)īelow that it sez "Reserve address by-should be on "MAC address"īelow that where it sez "MAC Address, type the MAC address you wrote down from the Xbox One(remember, it's gotta be EXACT)īelow that where it sez IPv4: type in 10.0.1.253(it might have part of it already there, like 10.0.1.2. Make sure router mode is set to "DHCP and NAT"Īt the bottom of the empty box that sez "DHCP reservations" click the + signĪ drop down menu will open. On your Mac: Go to Finder/Applications/Utilities/Airport utilityĬlick on the the Airport Extreme or Airport Time capsule icon Settings/Network/Advanced Settings: write down the wired or wireless MAC address on the right(depending on what type of connection you have). How to put your Xbox One in the DMZ w/ an Apple router in Mac OS X: Then select the DNS address section and select manual.Įnter the primary and secondary DNS addresse you took note of earlier (these are found in the Internet tab of Airport Utility) Select the gateway address and enter the LAN IP address here (ound on the first display screen of Airport Utility by clicking the Airport Extreme picture). Select the subnet mask and enter the subnet mask of your network (remember this was what you wrote down from the internet tab in Airport Utility) Select the IP address and enter the IP address your Extreme gave you when enabling default host. Select the IP address section and choose manual. Go to the network configuration screen on your xBox. Now you need to manually configure your netwrok settings on the xBox. Once all this is done select Update to load these settings to the Airport Extreme. Repeat these steps for all the ports listed above. Private IP address (make sure this matches the address you wrote down when you enabled the default host. You need to setup several ports (53,80,88,1863, and 3074) to be forwarded to the xBox IP address. Go to the Port Settings section on the Network tab. It will be the address for your xBox.Ĭlose this didalog box by selecting SAVE. Take note of this address you will need it later. When you select the Enable Default host it will give you an IP address. Select the Network options button (near the bottom of the page)Įnsure Enable NAT Port Mapping Protocol is selected.Įnsure Enable Default host at: is selected. just the normal stuffĪlso take note of your Subnet Mask DNS server addresses ( you will need them later) Take note of the LAN IP address (you will need this later). I am using a 5th generation airport extreme and Airport Utility 6.1.įirst click on your Airport Extreme in the first display of Airport Utility. It seems a lot of people have struggled with this so I thought I would share what has worked for me.
0 Comments
Leave a Reply. |